نبذة مختصرة : An experimental and theoretical study of the process of the equal−channel angular pressing (ECAP) was performed to obtain a thermoelectric (TE) material based on bismuth telluride. A brief review of the mathematical modeling of the ECAP process is given. The influence of the ECAP design features and temperature modes on the process of plastic forming is considered. The results of calculations of the thermally stressed state of samples at different stages of the ECAP process are presented. The calculations of the ECAP process were carried out by means of Lagrangian finite element mesh, which adjusted adaptively during the process to the die geometry and became finer or coarser depending on the magnitude of the plastic deformation. It was required for the specified calculation accuracy and the convergence of iterative process. The results of an experimental study of the structure and properties of samples obtained by the ECAP using a set of measuring methods (X−ray diffractometry and electron microscopy) are discussed. The thermoelectric characteristics of the obtained materials were measured by Harman method. Comparative methodical calculations of the ECAP process for TE materials based on bismuth telluride have been made by adjusting parameters determining the grain formation (i.e. the critical plastic deformation as a function of temperature and power−law dependence of its rates). It made possible to adjust the ECAP model on the basis of the measured grain sizes for TE materials . The calculation results of grain creation during the plastic forming, which are compared with the measurement data, are presented. The practical result of this research was the improved geometry of the die and the validated technological regimes of plastic deformation, which allowed obtaining samples with the good TE efficiency.
Relation: https://met.misis.ru/jour/article/view/242/209; Im J.−T. Grain refinement and texture development of cast BiSb alloy via severe plastic deformation. − Yeung University (S. Korea), 2007. − 113 p.; Zhu W., Yang J. Y., Gao X. H., Hou J., Bao S. Q., Fan X. A. The underpotential deposition of bismuth and tellurium on cold rolled silver substrate by ECALE // Electrochimica Acta. − 2005. − V. 50, iss. 27. − P. 5465—5472. DOI:10.1016/j.electacta.2005.03.028; Ashida M., Hamachiyo T., Hasezaki K., Matsunoshita H., Horita Z. Effect of high pressure torsion on crystal orientation to improve the thermoelectric property of a Bi2Te3−based thermoelectric semiconductor // Adv. Mater. Res. − 2010. − V. 89–91. − P. 41—46. DOI:10.4028/www.scientific.net/AMR.89-91.41; Ceresara S., Codecasa M., Passaretti F., Tomeš F., Weidenkaff F., Fanciulli C. Thermoelectric properties of in situ formed Bi0.85Sb0.15/Bi−rich particles composite // J. Electronic Materials. − 2011. − V. 40, iss. 5. − P. 557—560. DOI:10.1007/s11664-010-1450-7; Im J.−T., Hartwig K. T., Sharp J. Microstructural refinement of cast p−type Bi2Te3—Sb2Te3 by equal channel angular extrusion // Acta Materialia. − 2004. − V. 52, iss. 1. − P. 49—55. DOI:10.1016/j.actamat.2003.08.025; Kim Hyoung Seop, Quang Pham, Seo Min Hong, Hong Sun Ig, Baik Kyeong Ho, Lee Hong Rho, Nghiep Do Minh. Process modelling of equal channel angular pressing for ultrafine grained materials // Materials Transactions. − 2004. − V. 45, N 7. − P. 2172— 2176. DOI:10.2320/matertrans.45.2172; Maciejewski J., Kopeć H., Petryk H. Finite element analysis of strain non−uniformity in two processes of severe plastic deformation // Engineering Transactions. − 2007. − V. 55, N 3. − P. 197—216.; Aour B., Mitsak A. Analysis of plastic deformation of semi− crystalline polymers during ECAE process using 135° die // J. Theoretical and Applied Mechanics. − 2016. − V. 54, N 1. − P. 263—275. DOI:10.15632/jtam-pl.54.1.263; Beyerlein I. J., Lebensohn R. A., Tomé C. N. Modeling texture and microstructural evolution in the equal channel angular extrusion process // Materials Science and Engineering A. − 2003. − V. 345, iss. 1–2. − P. 122—138. DOI:10.1016/S0921-5093(02)00457-4; Parshikov R. A., Rudskoy A. I., Zolotov A. M., Tolochko O. V. Technological problems of equal channel angular pressing // Rev. Adv. Mater. Sci. − 2013. − V. 34. − P. 26—36. URL: http://www.ipme.ru/e-journals/RAMS/no_13413/04_13413_tolochko.pdf; Luis C. J., Salcedo D., Luri R., León J., Puertas I. FEM modelling of the continuous combined drawing and rolling process for severe plastic deformation of metallic materials // In book: Numerical modeling of materials under extreme conditions. Advanced structured materials. V. 35. − Berlin; Heidelberg: Springer, 2014. − P. 17—45. DOI:10.1007/978-3-642-54258-9_2; Basavaraj P. 3D finite element simulation of equal channel angular pressing with different material models // International Journal of Emerging Technologies and Innovative Research. − 2016. − V. 3, iss. 3. − P. 16—28. URL: http://www.jetir.org/view?paper=JETIR1603005; Krállics G., Széles Z., Malgyn D. Finite element simulation of multi−pass equal channel angular pressing // Materials Science Forum. − 2003. − V. 414–415. − P. 439—444. DOI:10.4028/www.scientific.net/MSF.414-415.439; Богомолов Д. И. Структура и свойства низкотемпературных термоэлектрических материалов, полученных интенсивной пластической деформацией // Автореф. дис. … канд. техн. наук. − М.: МИСиС, 2013. − 23 с.; Егер Дж. К. Упругость, прочность и текучесть. − М.: Машгиз, 1961. − 170 с.; Лаврентьев М. Г., Меженный М. В., Освенский В. Б., Простомолотов А. И. Математическое моделирование процесса экструзии термоэлектрического материала // Изв. вузов. Материалы электронной техники. − 2012. − № 3. − С. 35—40. DOI:10.17073/1609-3577-2012-3-35-40; MSC.Marc Volume A: Theory and User Information. MSC. Software Corporation. 2008. 805 p. URL: https://simcompanion.mscsoftware.com/infocenter/index?page=content&id=DOC9245; Mitsak A., Aour B., Khelil F. Numerical investigation of plastic deformation in two−turn equal channel angular extrusion // Engineering, Technology & Applied Science Research. − 2014. − V. 4, N 6. − P. 728—733. URL: http://etasr.com/index.php/ETASR/article/view/517; Li S., Bourke M. A. M., Beyerlein I. J., Alexander D. J., Clausen B. Finite element analysis of the plastic deformation zone and working load in equal channel angular extrusion // Materials Science and Engineering A. − 2004. − V. 382, iss. 1–2. − P. 217—236. DOI:10.1016/j.msea.2004.04.067; Bogomolov D. I., Bublik V. T., Tabachkova N. Yu., Tarasova I. V. Properties and formation of the structure of Bi2Se0.3Te2.7 solid solutions produced by equal−channel angular pressing // J. Electronic Materials. − 2016. − V. 45, N 1. − P. 403—410. DOI:10.1007/s11664-015-4110-0; Простомолотов А. И., Верезуб Н. А. Динамическое моделирование пластического формования термоэлектрического материала методом горячей экструзии // Вестник Тамбовского ГУ им. Г. Р. Державина. Cер. Естественные и технические науки. − 2016. − Т. 21, № 3. − С. 818—821. DOI:10.20310/1810-0198-201621-3-818-821; https://met.misis.ru/jour/article/view/242
Rights: Authors who publish with this journal agree to the following terms:Authors retain copyright and grant the journal right of first publication with embargo 1 year, then the work will be licensed under a Creative Commons Attribution License that allows others to share the work with an acknowledgement of the work's authorship and initial publication in this journal.Authors are able to enter into separate, additional contractual arrangements for the non-exclusive distribution of the journal's published version of the work (e.g., post it to an institutional repository or publish it in a book), with an acknowledgement of its initial publication in this journal.Authors are permitted and encouraged to post their work online (e.g., in institutional repositories or on their website) prior to and during the submission process, as it can lead to productive exchanges, as well as earlier and greater citation of published work (See The Effect of Open Access). ; Авторы, публикующие статьи в данном журнале, соглашаются на следующее:Авторы сохраняют за собой автороские права и предоставляют журналу право первой публикации работы, которая по истечении 12 месяцев после публикации автоматически лицензируется на условиях Creative Commons Attribution License , которая позволяет другим распространять данную работу с обязательным сохранением ссылок на авторов оригинальной работы и оригинальную публикацию в этом журнале.Авторы имеют право размещать их работу в сети Интернет (например в институтском хранилище или персональном сайте) до и во время процесса рассмотрения ее данным журналом, так как это может привести к продуктивному обсуждению и большему количеству ссылок на данную работу (См. The Effect of Open Access).
Processing Request
No Comments.