نبذة مختصرة : The region of the Argentine Northwest presents a development of the olive activity with excellent productive results destined to the Oil Industry. However, this productive evolution brought with it the need to treat those solid residues produced by this food industry. That is why the National University of La Rioja is working on priority lines on Control and Protection of the Environment within a model of sustainable development with the aim of reducing this industrial waste that ends up in dumps or sanitary landfills. In this sense, the present investigation seeks to recycle them in chipboard to later determine and analyze their physical and mechanical properties. The tested specimens turned out to have a good behavior before cutting processes. The density of the agglomerate presented a high-density profile, being beneficial, since low-density materials are more likely to suffer the rigors of humidity. The moisture test showed an adequate setting index and the swelling test indicated resistance to the influence of water. Regarding the flexural strength, the results indicated that the deformation due to maximum load and the flexural deformation at breakage are greater in the case of the pomace agglomerate, being the maximum flexural load the most unfavorable factor of the test specimens, pomace base. ; La región del Noroeste Argentino presenta un desarrollo de la actividad olivícola con excelentes resultados productivos destinados a la Industria aceitera. Sin embargo, esta evolución productiva trajo aparejada la necesidad de tratar aquellos residuos sólidos producto de esta industria alimenticia. Es por ello que la Universidad Nacional de La Rioja se encuentra trabajando en líneas prioritarias sobre Control y Protección del Medio Ambiente dentro de un modelo de desarrollo sustentable con el objetivo de disminuir estos desechos industriales que terminan en vertederos o en rellenos sanitarios. En este sentido la presente investigación busca reciclarlos en placas de aglomerado para luego determinar y analizar sus ...
Relation: https://revistas.ucm.es/index.php/OBMD/article/view/85272/4564456562286; Balaz, P. (2008). Mechanochemistry in Nanoscience and Minerals Engineering. ISBN: 978-3- 540-74854-0 (2008). Springer- Velag Berlin Heidelberg. https://books.google.com.ar/books?id=FldqbSffUMgC&printsec=frontcover&hl=es#v=one page&q&f=false. Becerra Martínez J. 1976 Algunas Características Físicas y Mecánicas de Tableros de Partículas Producidos en México y sus probables usos en la Construcción- Ciencia Forestal. (1) 2. pp 33-40. http://revistas.inifap.gob.mx/index.php/Forestales/article/view/859/857. Bohnet M. (2003). Mechanische Verfahrenstechnik. WILEY ‐ VCH Verlag GmbH. 10.1002/9783527663569. Cunninggham, J.C.; Sinka, I.C. y Zavaliangos, A., (2004) Analysis of Tablet Compaction. I. Characterization of Mechanical Behaviour of Powder and Powder/Tooling Friction. Journal of Pharmaceutical Sciences, 93 (8), 2022-2039. https://www.academia.edu/47526786/Analysis_of_tablet_compaction_I_Characterization_ of_mechanical_behavior_of_powder_and_powder_tooling_friction. Contreras, W.; Owen, M.E.; Garay D. y Contreras Y.M. (2006). Diseño de Tableros Aglomerados de Partículas de Caña Brava (Gynerium sagittatum) y Adhesivo Fenol- Formaldehído. Revista Forestal Lat. 43(2), pp 39- 55 http://www.saber.ula.ve/bitstream/handle/123456789/24136/articulo3.pdf?sequence=2Jian ping W. y Chanchan W. (2012). Adhesives derived from agricultural proteins. https://patents.google.com/patent/CA2839344A1/en. Fiplasto (2019). Introducción a La Fabricación Mundial de Tableros Basados en la Madera. http://www.fiplasto.com.ar/ingles/Mercado_Tableros.doc. Fono-Tamo, R.S.; Idowu, O.O. y Koya F.O. (2014). Development of Pulverized Palm Kernel Shells Based Particleboard International Journal of Material and Mechanical Engineering IJMME (3) 3, August 2014 DOI:10.14355/ijmme.2014.0303.01. http://www.ijmme. org/paperInfo.aspx?ID=15255. García Triñanes P. (2010). Avances en Aglomeración y Compactación de Partículas [Tesis]. https://dspace.usc.es/xmlui/bitstream/handle/10347/2822/9788498874266_content.pdf?seq uence=1&isAllowed=y Gabbott I. (2007) University of Sheffield, Department of Chemical & Process Engineerin. http://etheses.whiterose.ac.uk/3605/1/440953.pdf. Guru, M.; Tekeli y S. and Bilici, I. (2006). Manufacturing of urea formaldehyde based composite particleboard from almond shell. Materials and Design 27: 1148-1151. http://www.sciencedirect.com/science/article/pii/S0261306905000774. Heckel, R.W. (1961) Analysis of powder compaction phenomena. Trans. Metall Soc. AIME 221, 1001–1008. Instituto Nacional de Estadística y Censo (2018). Censo Nacional Agropecuario https://www.indec.gob.ar/indec/web/Nivel4-Tema-3-8-87. Khoei, A. R.; Keshavarz, Sh. y Khaloo A.L. (2008). Modeling of large deformation frictional contact in powder compaction processes. Applied Mathematical Modelling. 32, 775–801.http://www.sciencedirect.com/science/article/pii/S0307904X07000534. Lazić Z.R. (2004) Design of Experiments in Chemical Engineering. A practical Guide. Wiley ‐VCH Verlag GmbH & Co. KGaA. DOI 10.1002/3527604162. Matsumoto R.L.K. (1986) Generation of powder compaction response diagrams. Journal of the American Ceramic Society. 69, 246-247. Michrafy, A.; Dodds, J.A. y Kadiri M.S. (2004) Wall friction in the compaction of pharmaceutical powders: measurement and effect on the density distribution. Powder Technology.148, 53– 55. Michrafy, A.; Ringenbacher, D. y Tchoreloff, P. (2002) Modelling the compaction behaviour of powders: application to pharmaceutical powders. Powder Technology. 127, 257-266. Mort P. (2005). Scale-up of binder agglomeration processes. Powder Technology. 150, 86-103. https://www.sciencedirect.com/journal/powder-technology/vol/150/issue/2. Perry, R.H. y Green D.W. (2008). Perry’s Chemical Engineers Handbook. 8th Ed. Mc Graw Hill. Programa de Fortalecimiento Institucional Productivo y de Gestión Fiscal Provincial. (2009). Estudio de Mercado del Sector Olivícola http://www.isportal.com.ar/imagenes/ESTUDIO_DE_MERCADO_- _SECTOR_OLIVICOLA.pdf. Rocha, Almeida R.; Del Menezzi, C.H.S. y Teixeira D.E. (2002). Utilization of the coconut shell of babaçu (Orbignya sp.) to produce cement-bonded particleboard. Bioresource Technology, 85: 159-163. https://www.sciencedirect.com/science/article/pii /S0960852402000822=663763442&_sort=r&_st=13&view=c&md5=c592a64475 0848964d6dfa0cec3a27e4&searchtype=a. Sampathrajan, A.; Vijayaraghavan, N.C. y Swaminathan, K.R. (1992). Mechanical and thermal properties of particleboards made from farm residues. Bioresource Technology 40: 249-251. http://www.sciencedirect.com/science/article/pii/096085249290151M. Sotomayor Castellanos J.R (2003). Caracterización Mecánica de Madera Reconstituida Maderas. Maderas. Ciencia y tecnología. 5(1): 20-43. http://dx.doi.org/10.4067/S0718- 221X2003000100002 .; https://revistas.ucm.es/index.php/OBMD/article/view/85272
Processing Request
No Comments.