نبذة مختصرة : Asymmetric rolling of aluminum alloys is one of the methods for improving their mechanical and performance characteristics. Kinematic asymmetry during rolling is achieved by varying the roll speed ratios (V1 /V2). It is believed that when V1 /V2 > 3, the process of asymmetric rolling, by combining significant compression and shear deformations, approximates the processes of severe plastic deformation. It has been found that the majority of studies are based on data obtained within a limited roll speed ratio range, V1 /V2 < 2, in asymmetric rolling. This article examines the effects observed at V1 /V2 = 1÷7.7. The implementation of this condition became possible thanks to a unique scientific facility – the 400 laboratory-industrial asymmetric rolling mill at the Zhilyaev laboratory “Mechanics of Gradient Nanomaterials” at Nosov Magnitogorsk State Technical University Experiments were conducted on asymmetric thin-sheet rolling of aluminum alloys 2024, 5083, and 6061, as well as accumulative roll bonding to produce laminated sheet aluminum composites 5083/2024, 5083/1070, and 6061/5083. The disadvantages of asymmetric rolling compared to symmetric rolling were identified: sample failure was observed at single relative reductions of 37 % for layered sheet aluminum composites (5083/2024) and 40 % for thin-sheet aluminum alloys (6061). The nuances of material preparation for processing were described, including the necessity of cleaning and degreasing the alloy surfaces before bonding into a composite. The rolling temperature regimes were selected, determining cold asymmetric thin-sheet rolling (room temperature processing) and warm asymmetric accumulative roll bonding (heating of the workpieces in the furnace before rolling at 320–350 °C). A reduction in rolling force (by a minimum of 1.3 times), the ability to vary hardness (including an increase by a minimum of 30 %), and technological plasticity with changes in the roll speed ratios within the range of 2 to 7.7 were demonstrated. Options were proposed for ...
Relation: https://cvmet.misis.ru/jour/article/view/1646/766; https://cvmet.misis.ru/jour/article/view/1646/767; Youzhi Li, Yongfeng Shen, Sixin Zhao, Weina Zhang, Xue W.Y. Strengthening a medium-carbon low-alloy steel by nanosized grains: The role of asymmetrical rolling. Nanomaterials. 2023;13(5):956. https://doi.org/10.3390/nano13050956; Muñoz J.A., Avalos M., Schell N., Brokmeier H.G., Bolmaro R. Comparison of a low carbon steel processed by cold rolling (CR) and asymmetrical rolling (ASR): Heterogeneity in strain path, texture, microstructure and mechanical properties. Journal of Manufacturing Processes. 2021;64:557—575. https://doi.org/10.1016/j.jmapro.2021.02.017; Graça A., Vincze G., Wen W., Butuc M.C., Lopes A.B. Numerical study on asymmetrical rolled aluminum alloy sheets using the visco-plastic self-consistent (VPSC) method. Metals. 2022;12(6):979. https://doi.org/10.3390/met12060979; Tao Zhang, Lei Li, Shi-hong Lu, Jia-bin Zhang, Hai Gong. Comparisons of flow behavior characteristics and microstructure between asymmetrical shear rolling and symmetrical rolling by macro/micro coupling simulation. Journal of Computational Science. 2018;29: 142—152. https://doi.org/10.1016/j.jocs.2018.10.005; Guofu Xu, Xiaowu Cao, Tao Zhang, Yulu Duan, Xiaoyan Peng, Ying Deng, Zhimin Yin. Achieving high strain rate superplasticity of an Al—Mg—Sc—Zr alloy by a new asymmetrical rolling technology. Materials Science and Engineering: A. 2016;672:98—107. https://doi.org/10.1016/j.msea.2016.06.070; Ji Wang, Xianghua Liu, Xiangkun Sun. Study on asymmetrical cold rolling considered sticking friction. Journal of Materials Research and Technology. 2020;9(6):14131—14141. https://doi.org/10.1016/j.jmrt.2020.10.027; Amegadzie M.Y., Bishop D.P. Effect of asymmetric rolling on the microstructure and mechanical properties of wrought 6061 aluminum. Materials Today. 2020;25:101283. https://doi.org/10.1016/j.mtcomm.2020.101283; Tao Zhang, Lei Li, Shi-Hong Lu, Hai Gong, Yun-Xin Wu. Comparisons of different models on dynamic recrystallization of plate during asymmetrical shear rolling. Materials. 2018;11(1):151. https://doi.org/10.3390/ma11010151; Cunqiang Ma, Longgang Hou, Jishan Zhang, Linzhong Zhuang. Influence of thickness reduction per pass on strain, microstructures and mechanical properties of 7050 Al alloy sheet processed by asymmetric rolling. Materials Science and Engineering: A. 2016;650(5): 454—468. https://doi.org/10.1016/j.msea.2015.10.059; Šlapáková M., Kihoulou B., Grydin O. Development of microstructure of asymmetrically rolled AA3003 aluminium sheets with Zr addition. Journal of Alloys and Metallurgical Systems. 2023;2:100012. https://doi.org/10.1016/j.jalmes.2023.100012; Muñoz J.A., Khelfa T., Duarte G.A., Avalos M., Bolmaro R., Cabrera J.M. Plastic behavior and microstructure heterogeneity of anAA6063-T6 aluminum alloy processed by symmetric and asymmetric rolling. Metals. 2022;12(10):1551. https://doi.org/10.3390/met12101551; Vincze G., Simões F., Butuc M.C. Asymmetrical rolling of aluminum alloys and steels: A review. Metals. 2020;10(9):1126. https://doi.org/10.3390/met10091126; Sułek B., Krawczyk J., Majewski M., Nawida N., Plewa K. Analysis of the influence of kinematic and frictionasymmetry on the curvature of the strip and forceparameters of the rolling process. Tribologia. 2023; 305(3):81—94. https://doi.org/10.5604/01.3001.0053.9439; Sai Wang, Xianlei Hu, Xiaogong Wang, Jingqi Chen, Xianghua Liu, Changsheng Li. Design and experiment of V-shaped variable thickness rolling for rolled profiled strips. Journal of Materials Research and Technology. 2021;15:4381—4396. https://doi.org/10.1016/j.jmrt.2021.10.067; Biryukova O.D., Pesin A.M., Pustovoytov D.O. Investigation of the influence of kinematic asymmetry on the properties of laminated materials. Materials Research Proceedings. 2023;32:287—293. https://doi.org/10.21741/9781644902615-33; Biryukova O., Pesin A., Pustovoitov D. Experience in obtaining laminated aluminum composites by asymmetric accumulative roll bonding. Letters on Materials. 2022;12(4):373—378. https://doi.org/10.22226/2410-3535-2022-4-373-378; Pustovoytov D., Pesin A., Tandon P. Asymmetric (hot, warm, cold, cryo) rolling of light alloys: A review. Metals. 2021;11(6):956. https://doi.org/10.3390/met11060956; Biryukova O., Pesin A., Pustovoytov D., Kozhemiakina A., Nosov L. Obtaining laminated aluminum composites with a gradient structure based on asymmetric deformation. METAL. 2021;496—501. https://doi.org/10.37904/metal.2021.4133; Pesin A., Raab G., Sverchkov A., Pustovoytov D., Kornilov G., Bochkarev A., Pesin I., Nosov L. Development of asymmetric cold rolling technology of high-strength steel grades in order to exclude intermediate annealing operations. Materials Research Proceedings. 2023;32: 355—361.; Kosturek R., Mróz S., Stefanik A., Szota P.L., Gębara P., Merda A., Wachowski M., Gloc M. Study on symmetry and asymmetry rolling of AA2519-T62 alloy at room-temperature and cryogenic conditions. Materials. 2022;15(21):7712. https://doi.org/10.3390/ma15217712; Pan D., Sansome D.H. An experimental study of the effect of roll-speed mismatch on the rolling load during the cold rolling of thin strip. Journal of Mechanical Working Technology. 1982;6(4):361—377. https://doi.org/10.1016/0378-3804(82)90034-1; Aboutorabi A., Assempour A., Afrasiab H. Analytical approach for calculating the sheet output curvature in asymmetrical rolling: In the case of roll axis displacement as a new asymmetry factor. International Journal of Mechanical Sciences. 2016;105:11—22. https://doi.org/10.1016/j.ijmecsci.2015.10.016; Qilin Zhao, Xianlei Hu, Xianghua Liu. Analysis of mechanical parameters in multi-pass asymmetrical rolling of strip by slab method. Materials. 2023;16(18):6286. https://doi.org/10.3390/ma16186286; Zejun Chen, Hongbo Hu, Xia Wu, Minhong Zhou, Kawunga Nyirenda, Qing Liu, Guojun Wang, Deman Wang. Effect of cross accumulative roll bonding process on microstructure and mechanical properties of laminated 1100/7075 composite sheets. TMS (The Minerals, Metals and Society). 2013;2285—2295. https://doi.org/10.1002/9781118792148.ch284; Mehtedi M.E., Lai D., Mohtadi R.E., Carta M., Buonadonna P., Aymerich F. Bonding of similar AA3105 aluminum alloy by accumulative roll bonding process. ESAFORM. 2021;942/1—942/11. https://doi.org/10.25518/esaform21.942; Seleznev M., Renzing C., Schmidtchen M., Prahl U., Biermann H., Weidner A. Deformation lenses in a bonding zone of high-alloyed steel laminates manufactured by cold roll bonding. Metals. 2022;12:590. https://doi.org/10.3390/met12040590; Karganroudi S.S., Nasab B.H., Rahmatabadi D., Ahmadi M., Gholami M.D., Kasaeian-Naeini M., Hashemi R., Aminzadeh A., Ibrahim H. Anisotropic behavior of Al1050 through accumulative roll bonding. Materials. 2021;14:6910. https://doi.org/10.3390/ma14226910; https://cvmet.misis.ru/jour/article/view/1646
Processing Request
No Comments.